Studi Pengecoran Aluminium Dengan Metode Centrifugal Casting Dengan Variasi Kemiringan Cetakan 0˚, 15˚, 30˚ Terhadap Komposisi Kimia, Density, Porositas Dan Struktur Mikro

Sriyani, Mamik and , Patna Partono, S.T., M.T. (2020) Studi Pengecoran Aluminium Dengan Metode Centrifugal Casting Dengan Variasi Kemiringan Cetakan 0˚, 15˚, 30˚ Terhadap Komposisi Kimia, Density, Porositas Dan Struktur Mikro. Skripsi thesis, Universitas Muhammadiyah Surakarta.

	PDF (Halaman Depan) HALAMAN DEPAN.pdf Download (735kB)
	PDF (Bab I) BAB I.pdf Download (105kB)
	PDF (Bab II) BAB II.pdf Restricted to Repository staff only Download (667kB) | Request a copy
	PDF (Bab III) BAB III.pdf Restricted to Repository staff only Download (526kB) | Request a copy
	PDF (Bab IV) BAB IV.pdf Restricted to Repository staff only Download (738kB) | Request a copy
	PDF (Bab V) BAB V.pdf Restricted to Repository staff only Download (156kB) | Request a copy
	PDF (Daftar Pustaka) DAFTAR PUSTAKA.pdf Download (255kB)
	PDF (Surat Pernyataan Publikasi) SURAT PERNYATAAN PUBLIKASI.pdf Restricted to Repository staff only Download (144kB) | Request a copy
	PDF (Naskah Publikasi) NASKAH PUBLIKASI (19).pdf Download (833kB)

Abstract

The purpose of this study was to determine the effect of 0o, 15o, 30o mold slope variations with the centrifugal casting method on the chemical composition, density, porosity and microstructure with the main material Aluminum from the used piston. In this study using the Centrifugal die casting method. 750oC pour temperature and 700rpm motor rotational speed. The slope of the mold varies into angles 0o, 15o, 30o. Chemical composition testing using Emmision Sprectometer (ASTM E-1251) test equipment. Calculation of density is done by calculating the mass and volume of the cast. Observation of porosity using a digital microscope. Micro structure testing using a metallographic microscope (ASTM E3-11). Test results The chemical composition of this material contains (Al) 85.20%, (Si) 11.34%, (Cu) 1.499%, (Ni) 1.1024%, (Fe) 0.5736% and other elements . Refer to ASTM B.85 standard classified into Al-Si (Aluminum - Silicon) A413.0. The test results of the Centrifugal die casting method density 0˚, 15˚, 30˚ have a value of density with a value of 2.7324 gr / cm3, 2.7324 gr / cm3, 2.7621 gr / cm3. From these data it can be concluded that the greater the density, the less porosity. The results of microstructure testing of cast products with a slope of 0o show the spread of β (Si) phases far apart and have large granular shapes. In cast products with a slope of 15o β phase (Si) it looks more closely and a little smaller. In cast products with a slope of 30o, the β (Si) phase is closed and small.

Item Type:	Karya ilmiah (Skripsi)
Uncontrolled Keywords:	centrifugal casting, tilt mold, aluminum, chemical composition, density, porosity, micro structure
Subjects:	T Technology > T Technology (General) T Technology > TJ Mechanical engineering and machinery
Divisions:	Fakultas Teknik > Teknik Mesin
Depositing User:	MAMIK SRIYANI
Date Deposited:	05 Nov 2020 06:25
Last Modified:	05 Nov 2020 06:25
URI:	http://eprints.ums.ac.id/id/eprint/86921

Actions (login required)

View Item